Zhengdong and you self -made float

Hello everyone, for fishing enthusiasts, it is essential to have several floating floats with good intentions. Today, we will learn how to make floats with you.

正东和您自制浮漂

first

Material selection:

正东和您自制浮漂

Based on the thickness of the drifting type to be made, the thickness of the south with a suitable length and the right length, and cannot be bent.

Drifting

Determine the length of the drifting shoulder according to the drifting type, wrap it with beautiful paper. It should be noted here that if you make a short drift floating, do not cut the reeds first. You can mark the length of the entire drifting body first, and cut it after finishing the shoulders, so that it is easy to operate. Slowly you will understand the importance of this step.

正东和您自制浮漂

Cut head:

正东和您自制浮漂

As shown in the figure, first cut the reeds first, and you must wait, otherwise it will affect the concentricity of the floating drift. You can cut the position from the knife to the beautiful paper paper. Do not cut over your head.

After the four -class portion, use the pen to make the mark point in the middle of each petal.

正东和您自制浮漂

As shown in the figure, novice suggestions are recommended to do auxiliary lines, which will not be very different when cutting.

The first knife is like this. At first I remember not to cut too much, once I cut it, I scrapped it.

正东和您自制浮漂

After cutting the remaining several petals in turn.

Polish

正东和您自制浮漂

When grinding, slowly grind, repair slowly, and try it slowly until the two petals are nearing can be seamlessly connected.

Shape:

The alcohol lamp is first baked the thermal shapinger, and then the drifting blank is inserted into the shaped device in a rotating manner, and repeated several times.

Complete shoulders?

正东和您自制浮漂

The same method does the drifting part:

At this time, it should be noted that because the drifting body is short, the shapinger grows over the body, and the operation is inconvenient, so we can make a small tool to solve this problem.

正东和您自制浮漂

Take a reed that is thinner in the shaped device, wraps a few rounds of beautiful paper on the top, and use it to put it in and insert it. as the picture shows.

The whole body was shaped.

正东和您自制浮漂

Drift tail, drift your feet

正东和您自制浮漂

Use white latex to be evenly applied to the cutting surface of the drifting blank. Use a cotton thread to bundle the method of 8 words. After the tie is tied, insert the appropriate length of drift tail, drift your feet, and principle. length. The diameter of the drifting tail will change with different drifting types.

Note that when you are tied, pay attention to adjusting concentricity, you can also use the concentric needle. After the tie is tied, the next step can be carried out after 36 hours

正东和您自制浮漂

This is another demonstration that can be removed.

In order to set the top top, at this time, the drifting tail and drifting feet were required for explosion -proof treatment. I will reinforce it with the suture of the surgery.

This is a golden line burst

Explosion -proof treatment of drifting tails and drifting feet

正东和您自制浮漂

Paint the bottom twice first. I personally, the paint ratio is the painting, curing agent, diluent: 1: 0.6: 0.5, wait for 36 hours to polish, then twice, then polish, if the surface is not on the surface, if the surface is not on the surface, if the surface is not on the surface, if the surface is not on the surface, if the surface is not on the surface, the surface does not surface. After the smooth polishing, there are two ways to float on the paint. One is the paint. The two disposable cups repeatedly pour the paint to the body. The second is immersion, and the paint tube is used.

Pour the tuned paint into the tube, put it in the float and lift it gently, do not touch the tube wall. To control the thickness of the paint, this will affect the self -weight and lead of the float.

正东和您自制浮漂

After the paint process is processed, the tail is used to color the tail, and the whole drift tail is coated with all yellow

正东和您自制浮漂

Repeat 3 times, remember that there is no clump on the tail, it must be uniform.

正东和您自制浮漂

Compared with the same length, the black interval is marked and painted according to different color intervals.

After painting!

正东和您自制浮漂

The float I made in the early days will do the test water test

正东和您自制浮漂

72 hours will be completed without changing.

正东和您自制浮漂

Personally do the simple process of drifting, please give pointers.

I think it’s okay, leave a message inquiries where I don’t understand.

正东和您自制浮漂

Shape:

Author: ArticleManager